- #Remington 336 rifle serial number lookup how to
- #Remington 336 rifle serial number lookup serial number
- #Remington 336 rifle serial number lookup free
We have recently learned that some Ruger Precision Rifles fitted with aluminum bolt shrouds may exhibit interference between the bolt shroud and the cocking piece (also known as the firing pin back). Why are you issuing a Safety Bulletin for the Precision Rifle? If you have any questions or concerns regarding this safety bulletin, please contact Customer Service at 33. As you lift the bolt handle, expect that raising the bolt may cause the rifle to fire. If your rifle fails to fire when you pull the trigger, you should keep the rifle pointed in a safe direction and wait 30 seconds before slowly lifting the bolt handle. Always keep your rifle pointed in a safe direction and treat every firearm as though it is loaded. It is important to always follow the rules of gun handling safety. "Arms Makers for Responsible Citizens®." We are firmly committed to safety and appreciate your patience and While we sincerely regret the need to issue this safety bulletin, our motto is, and has been for many years, We will then coordinate with them on shipment of your Once all authorizations are in place, we will begin shipping Here is what you can expect.īecause of international licensing requirements, there will be a delay before replacement bolt Thank you for signing your rifle up for the Ruger Precision Rifle® safety bulletin.
#Remington 336 rifle serial number lookup serial number
View Bolt Shroud Replacement InstructionsĮnter your Ruger Precision Rifle ® serial number below to determine if it is subject to the safety bulletin. Please use the serial number lookup to verify whether your rifle is potentially affected. Note: Some rifles have been fitted at the factory with replacement bolt shrouds that do not bear this dimple. If your bolt shroud has this mark, it was manufactured with the new design and no further action is needed. Replacement bolt shrouds of the new design are easily identified by the presence of a round dimple on the angled surface directly behind the firing pin back. Thus, if you have a Ruger Precision Rifle with a serial number beginning with 1802, 1803 or higher, your rifle is not affected. Newly manufactured Ruger Precision Rifles will begin with serial number prefixes 18.
#Remington 336 rifle serial number lookup how to
How to Determine if Your Bolt Shroud Has Been Replaced You will be asked to provide us with the serial number of your rifle and contact information so we can send you a replacement bolt shroud with installation instructions.
#Remington 336 rifle serial number lookup free
If you believe your rifle is affected or are unsure if your rifle is affected, you can request a FREE replacement bolt shroud by by filling out the form below. If you are not sure whether your rifle has exhibited any light primer indents or failures to fire, or are in any way concerned about the safety of your rifle, please sign up for this offer and we will send you a FREE replacement bolt shroud. However, if you have ever experienced light primer indents or failure to fire while shooting or dry firing your rifle, you should obtain a replacement bolt shroud, which Ruger will provide FREE of charge.Īlternatively, if you have fired more than 100 rounds through your rifle with no issues or concerns (light primer indents or failures to fire), your rifle is unlikely to be affected and no additional action is necessary. Look up your serial number below and verify if that is the case.Īlthough all rifles with aluminum bolt shrouds within the above serial number range are potentially affected, most rifles will never experience this issue. If your rifle falls within the serial number range above and has an aluminum bolt shroud, it is potentially affected. How to Determine if Your Rifle is Affected In rifles where this condition exists, it often resolves itself as the parts wear and the interference is reduced. If the rifle fails to fire when the trigger is pulled, it may fire when the bolt handle is subsequently lifted. Possible results of this interference are light primer strikes or, in extreme cases, the rifle may not fire when the trigger is pulled. In rare instances, the interference can disrupt the firing mechanism and cause it to not function properly. Some Ruger Precision Rifles may experience interference between the aluminum bolt shroud and the cocking piece (also known as the firing pin back).
![remington 336 rifle serial number lookup remington 336 rifle serial number lookup](http://www.antiquearmsinc.com/images/winchester-1894-rifle-model-94-antique-production-30-30-38-55-octagon-blue-cc-marlin-1893-collection/winchester-1894-rifle-model-94-antique-production-30-30-38-55-octagon-blue-cc-marlin-1893-collection-16.jpg)
![remington 336 rifle serial number lookup remington 336 rifle serial number lookup](https://www.gunsamerica.com/UserImages/5212/900133757/wm_3319353.jpg)
Ruger Precision Rifles (regardless of caliber) that have an aluminum bolt shroud and fall within the following serial number ranges are potentially affected: 1800-26274 to 1800-78345 or 1801-00506 to 1801-30461. This Safety Bulletin does not apply to Ruger Precision Rifles with polymer bolt shrouds.